Yard Machines E660G Operator's Manual

Operator's ManualSnow ThrowerModelsE600E, $610E, E6COF$640F, E640E, E640FE640G, E660F, E660GIMPORTANT:READSAFETYRULESANDINSTRUCTIONSCAREFULLYWarn

Hairpin-Shift RodShift ArmAssemblyClipFigure 12LampWiring(IfEquipped)NOTE: A lamp is an optional feature of some modelsnow throwers. It is NOT standar

Traction/AugerControl Lock--------_Shift LeverAuger ControlDischarge ChuteChuteClean-out ToolAugerChute Directional ControlChoke._Spark PlugRecoil Sta

Attach spark plug wire to spark plug. Make certainthe metal loop on end of the spark plug wire (insidethe boot) is fastened securely over the metal ti

ToEngageDrive• With the engine running near top speed, move shiftlever into one of the five FORWARD positions ortwo REVERSE positions. Select a speeda

Drift Cutters(Optional Equipment)Drift cutters should be used when operating the snowthrower in heavy drift conditions.On models so equipped, drift cu

Frame CoverAugerHousingFigure 18• Remove the frame cover underneath the snowthrower by removing six self-tapping screws.• With the traction control re

Adjust skid shoes by loosening the four hex nutsand carriage bolts and moving skid shoes todesired position. Make certain the entire bottomsurface of

Shear BoltsBearingsBearingsFigure 23AugerShaft• At least once a season, remove shear bolts onauger shaft. Oil or spray lubricant inside shaft. Alsolub

ShavePlateandSkidShoesThe shave plate and skid shoes on the bottom of thesnow thrower are subject to wear. They should bechecked periodically and repl

SupportFrictionWheelii• Drain the gasoline from the snow thrower, or placea piece of plastic under the gas cap.• Tip the snow thrower up and forward,

TABLEOFCONTENTSContent PageImportant Safe Operation Practices ... 3Hardware Pack

SECTION9: OFF-SEASONSTORAGEWARNING: Never store engine with fuel intank indoors or in enclosed, poorly ventilatedareas where fuel fumes may reach an o

SECTION11: PARTSLIST111312REF. PARTNO. NO.1 618-01232 618-01243 710-06424 711-0908A711-0909A711-0910A5 714-01616 715-01437 717-05288 717-05269 718-018

33\ModelsE6OOE,$610E,E640E,E640F,$640F,E640G,E660F,E6COF& E660G16 33 9_18 566*65 10 8. 24 11317----_j_ ! 22 /2 /2O61 636452545745\2526273644534635

ModelsE6OOE,$610E,E640E,E640F,$640F,E640G,E660F,E6COF& E660GREF.NO.12345678910111213141516171819202122232425262728293031323334353637PARTNO.714-050

ModelsE6OOE,$610E,E640E,E640F,$640F,E640G,E660F,E6COF& E660Gf323439 38T3745 40 /3513\736//21296\5 4\Drive Clutch CableAuger Clutch Cable3449 10124

ModelsE6OOE,$610E,E640E,E640F,$640F,E640G,E660F,E6COF& E660GREF.NO.123456789101112131415161718192O2122231-UsePARTNO.710-1652784-5688784-5687A756-0

ModelsE6OOE,$610E,E640E,E640F,$640F,E640G,E660F,E6COF& E660GREF.NO.1234567891011121314151618192O2122252627PARTNO.712-0116756-0178784-5632B710-0459

ModelsE6OOE,$610E,E640E,E640F,$640F,E640G,E660F,E6COF& E660G?IMPORTANT: For a proper working machine, use Factory Approved Parts.V-BELTS are speci

MANUFACTURER'S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTD LLC withrespect to new merchandise purchased and used in

SECTION1: IMPORTANTSAFEOPERATIONPRACTICESThis symbol points out important safety instructions, which if not followed, could endanger the personalsafet

4. Neveroperatewithamissingordamageddischargechute.Keepallsafetydevicesinplaceandworking.5. Neverrunanengineindoorsorinapoorlyventilatedarea.Engineexh

SECTION2: CONTENTSOFHARDWAREPACK(BoxedUnit)Lay out the hardware according to the illustration for identification purposes. Part numbers are shown inpa

SECTION3: ASSEMBLINGYOURSNOWTHROWERNOTE: This Operator's Manual covers several models.Snow thrower features vary by model. Not allfeatures discus

Securetheupperhandleandlowerhandlewiththetwoplasticwingknobs,cuppedwashersandcarriagebolt(eyeboltontheleftside)previouslyremoved.SeeFigure4.Figure 4•

CuppedCarriagBoltsLock NutsFigure 6Tighten the four hex bolts used earlier to attachbottom of the handles to the snow thrower frame.See Figure 5.Attac

After assembling all three chute flange keepers,tighten, then back off 1/4 turn to allow easiermovement of the chute. Use two 7/16" wrenches.Atta