TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma
10 se c t i O n 3 — as s e M b l y & se t -upAdjustmentsCutting HeightThe cutting height adjustment lever is located above the rear right wheel.
Controls and Features411Blade ControlThe blade control is attached to the upper handle of the mower. Depress and squeeze it against the upper handle t
Operation512Figure 5-1Starting EngineWARNING: Be sure no one other than the operator is standing near the lawn mower while starting engine or operatin
Maintenance & Adjustments613MaintenanceGeneral RecommendationsAlways observe safety rules when performing any • maintenance.The warranty on this l
14 se c t i O n 6— Ma i n t e n a n c e & ad j u s t M e n t sEngine CareA list of key engine maintenance jobs required for good performance by
15se c t i O n 6 — Ma i n t e n a n c e & ad j u s t M e n t sRemove back cover of speed control housing by removing 5. the three screws securin
Service7165. Lubricate the engine crankshaft and the inner surface of the blade adapter with light oil. Slide the blade adapter (and wave washer, if
17se c t i O n 7 — se r v i c eCarefully remove old battery and replace with new one. 4. Connect the positive lead to the positive side of the batter
18 se c t i O n 7— se r v i c eReplacing FuseThe electric starter circuit and battery are protected by a 40 ampere fuse. If the fuse burns out, the e
Troubleshooting819Problem Cause RemedyEngine Fails to start Blade control disengaged.1. Spark plug boot disconnected.2. Fuel tank empty or stale fuel.
Customer SupportPlease do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.If you have diffic
Troubleshooting820Problem Cause RemedyUneven cut Wheels not positioned correctly. 1. Dull blade.2. Place all four wheels in same height position 1. (i
Notes921
22Model Series J8605055542843424144114535121010232673937149513363115211917838144620485645122346184727345325302629169253040103332241026ABBA524659575846
23Ref No.Part Number Description1 746-04515 Drive Cable2 735-04059 Rubber Grommet3 687- 02417 Drive Control4 732-04516 Shift Spring5 747-04917A Blade
24Model Series J86045132946184342191644121415174021515027494728201237389791011AA1210558483332343536391302664232812232531222441
25Ref No.Part Number Description1 754 -04176 V-Belt2 732-04480A Spring Lever3 720-04092 Height Adjuster Knob4 717- 04452 Spur Gear, 16T - LH5 738-0427
Notes26
27nO t e s
MANUFACTURER’S LIMITED WARRANTY FORGDOC-100020 REV. AThe limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise pu
Important Safe Operation Practices23General OperationRead this operator’s manual carefully in its entirety before 1. attempting to assemble this mach
4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sA missing or damaged discharge cover can cause blade 12. contact or th
5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sServiceSafe Handling Of Gasoline:To avoid personal injury or property d
6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSpark ArrestorWARNING: This machine is equipped with an internal combu
7se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSight and hold this level with a vertical tree...or a corner of a build
Assembly & Set-Up38AssemblyNOTE: This unit is shipped without gasoline or oil in the engine. Fill up gasoline and oil as instructed in the accompa
9se c t i O n 3 — as s e M b l y & se t -upAttach center top of bag from inside of frame.c. Before attaching the grass catcher, the mulching baf
Comments to this Manuals